Jump to content
WAPT Forum

All Activity

This stream auto-updates     

  1. Last week
  2. scotthorton scotthorton joined the community
  3. Earlier
  4. flitlance flitlance joined the community
  5. finkup finkup joined the community
  6. sergei
    In most cases the user think times will be enough, but sometimes you need additional delays. For example into or after other operators.
  7. Nilam
    There is one option of Delay which we can use after any request....but since we can add think time then why we used delay operator?
  8. sergei
    1. No. WAPT doesn't collect such information. You can calculate the value only from a raw CSV file with the time statistics. 2. You can calculate the test duration: results.totalTimeUnits * results.timeUnitLength
  9. sergei
    Could you please provide your test results file?
  10. shehnaaz

    how to use perfmon in wapt ? n difference between perfmon n performance counter

    1. sergei

      sergei

      You can't use the perfmon in the WAPT, but WAPT can collect performance data with help of performance counters. You can find more info about performance counters on https://www.loadtestingtool.com/help/performance-counters.shtml

  11. shehnaaz

     how to use controller in wapt ?

    1. sergei

      sergei

      What do you mean by controller?

  12. shehnaaz

    can you plzz tell me difference between verification n run the test in wapt

    1. sergei

      sergei

      During verification WAPT runs only one virtual user usually without delays between requests.

  13. shehnaaz shehnaaz joined the community
  14. Mariselvam Mariselvam joined the community
  15. Mariselvam
    Hello WAPT Team, Scenario: In a profile, i have added task properties to group the pages. Results data: All the performance data(hits/sec, pages/sec, sessions/sec) is pertaining to the profile. Query1: In WAPT, can we get hits/sec at page or task level in table format? Query2: In WAPT Results "Analysis" section, how can we get the total test duration? Thanks.
  16. RANI started following Response Validation
  17. RANI
    Response body validation error showing under Response codes. But Test result showing as SUCCESS. But earlier when I get response body validation Error then Test result was showing as failure. Is there any configuration to get Test result= FAILURE, if response body validation error occurred.
  18. RANI RANI joined the community
  19. viktoriamodesta viktoriamodesta joined the community
  20. jennybonnet jennybonnet joined the community
  21. sergei
    Could you please describe what is your goal? What do you want to get? Why do you need to add jar files?
  22. Pooja joshi started following How to import packages or jars in WAPT JS
  23. Pooja joshi
    Hi team, How can we add jar files or how can we use import statements in WAPT JS operator?
  24. sergei
    You need to use the $File function https://www.loadtestingtool.com/help/functions.shtml#_file
  25. Nilam started following Uploading file from destop
  26. Nilam
    I am new to WAPT Tool, I am working on a script (filebin) in which I upload file from desktop... but when I change the name of file it just changes the name But I don't know how to pass the file path, because there is no value in Url parmeter, so is there any other way?
  27. Minefavseo Minefavseo changed their profile photo
  28. sergei
    Hi Jiri, There is no the such guide. You can find out some information in the WAPT help and use existing counters as examples.
  29. jmundl started following Performance counters for system processes
  30. jmundl
    Hi Sergei, please, is somewhere any guide, that can explain how to write own performance counters? Best Regards, Jiri
  31. liamatson45 liamatson45 changed their profile photo
  32. sergei
    Did you install the client certificate in WAPT? Is your site available? Could you provide us your certificate?
  33. avin_mehya
    Yes client certificate is needed and the same has been installed in browser
  34. sergei
    Is a client certificate required for accessing to your site? Did you install it in the browser?
  35. avin_mehya started following X509 certificate error while verifying/recording scripts
  36. avin_mehya
    Hi, While verifying scripts for one of our websites we are receiving X509 certificate is required error. We had few scripts which were recorded two months back and above error appears when verifying them. Moreover when we try to record new scripts then we are getting below error. This website works fine on browser.
  37. sergei
    Unfortunately no.
  38. avin_mehya
    Thanks a lot Sergei. Overwriting option works fine. But there are a lot of requests with similar request headers. So can this be set globally in the Default HTTP Headers at Profile level. Because there i dont see a dropdown of Overwrite.
  39. sergei
    If you manually add the Content-Type header to the end of the headers list with the overwrite option it should overwrite the automatic default header. Could you give me you profile so I could check it?
  40. avin_mehya
    Hi, We have a situation here where the request headers are identical barring just one difference with respect to content type. In the recorded request this happens to be application/json while during test the charset gets appended to the content-type. Response is returning an 500 Internal Server error as the method is throwing Null Pointer exception. This request with charset was posted through browser as well and it failed. I tried to add a request header with the below values so it would overwrite the automatically generated header. But that returns with content-type. Is there a way where we can send this request by isolating the charset part from the content-type. Recorded Request content-type: application/json Test Request content-type: application/json; charset=UTF-8
  41. sergei
    Please, update your WAPT Pro to the latest build. If it will not resolve your issue, please give me your scenario and profile.
  42. bcg_stresstesting started following Running from Command Line
  43. bcg_stresstesting
    Hi! I just upgraded to WAPT Pro 5.0 from WAPT 7.5. I can attest that running WAPT Pro with the command line using the -run option just opens WAPT and doesn't load the scenario/profile. When I run with the -noui option, nothing appears to happen. The test I'm trying to run ramps up to 500 users with 1 user being added every 5 seconds. I have to be unwittingly omitting something. Any help out there? WAPT Pro > WAPT Pro 5.0 (64-bit) Built on Oct 6 2019 WAPT Pro > Load settings from file: C:\ProgramData\Softlogica\WAPT\settings.xml WAPT Pro > Loading profile from file: C:\StressTesting\Tab3.wppx. WAPT Pro > Load profile OK: C:\StressTesting\Tab3.wppx. WAPT Pro > Load scenario OK: C:\StressTesting\Tab3.wpsx. WAPT Pro > Load agent ****2 is online. WAPT Pro > Load agent localhost is online. WAPT Pro > Load agent localhost running users 0 WAPT Pro > Load agent ****2 running users 0 WAPT Pro > Test started. WAPT Pro > Load agent localhost running users 0 WAPT Pro > Load agent ****2 running users 0 WAPT Pro > Test finished.
  1. Load more activity
×
×
  • Create New...